| December 12, 2022 |
- IP stack - MTU settable
- IP stack - Improved processing of fragmented UDP packets
- System start - When boot error occurs update mode is activated for system restore
- MQTT - Publish is suppressed when <disable> is entered as payload
- OPC UA - URI query corrected
|
1.64
on request |
| November 3, 2022 |
- DHCP - Processing of the option flags expanded
- OPC UA - Transfer of application URI corrected
- Config Upload - Parameter transfer corrected
- System start - Configuration initialization optimized
|
1.63
on request |
| September 26, 2022 |
- Actions - up to 16 outputs on another Web-IO can be switched
- Actions - placeholders in the HTTP payload are supported
- Actions - for HTTP-POST without payload a content length of 0 is entered in the header
- OPC UA - NodeID overview can be recalled
- OPC UA - your own NodeIDs can be loaded via list
- OPC UA - setting outputs by writing the CurrentOutputState-Nodes is possible
- OPC UA - writing the input counters by writing the CurrentInputCounter-Nodes is possible
- MQTT - QoS2 processing revised
- Modbus-TCP - diagnostics querying expanded
- Input-Counter - problems with bi-directional counting fixed
- System - Config Upload optimized and accelerated
Note: If, in the existing configuration, multiple outputs are used in an action, this option must be reset following an update!
|
1.62
on request |
| April 5, 2022 |
- Passwords - non-allowed characters are rejected
- Firmware update: Initiating via button in the interface possible
- Emergency access - missing login page added
- SNMP - MIBs and OIDs expanded
- OPC UA - Node-IDs can be modified via list upload
- Actions - switching of multiple outputs optimized
Please use the newest included version of Wutility for the update.
|
1.56
on request |
| January 11, 2022 |
- HTTPS - Chunked transfer revised
- SSL/TLS - Certificate upload now possible again
- DHCP - IP assignment with DHCP relays adapted
- Boot sector - Emergency access when firmware update is interrupted now revised
Please use the newest included version of Wutility for the update.
|
1.54
on request |
| October 7, 2021 |
- Outputs - Pulse mode revised
- Inputs - Short pulse processing improved
- REST - Digest authentication corrected
- Homepage - Size of display tiles adjusted
- My Web Page - JavaScript optimized
|
1.52
on request |
| August 2, 2021 |
- Actions - HTTP Request Basic Auth. revised
- Actions - HTTP Request Digest Auth. revised
- Actions - HTTP Request POST revised
- Boot Up - Denial of Service by UDP flood blocked
|
1.51
on request |
| May 4, 2021 |
- OPC - OPC UA implemented
- TLS - Uploading your own certificates is possible
- Actions - REST token timeout adjusted
- Actions - REST compatibility improved
- Pulse Mode - Internal handling improved
|
1.50
on request |
| August 12, 2020 |
- SSL/TLS - TLS stack expanded with Version 1.2
Reverting to firmware revisions lower than V1.36 is no longer possible after this update!
After the update a restart (simple reset) of the Web-IO is required
To load this firmware, WuTility must be used in the newest version included!
|
1.44
on request |
| July 2, 2020 |
- Socket-API - counterclear - set value corrected
- Web-API - counterclear - set value corrected
- Web-API - Cross Origin Request expanded
- Actions - POST added to HTTP requests
- Actions: Token authentication possible with HTTP requests
Reverting to firmware revisions lower than V1.36 is no longer possible after this update!
After the update a restart (simple reset) of the Web-IO is required
To load this firmware, WuTility must be used in the newest version included!
|
1.43
on request |
| March 5, 2020 |
- Actions - Cold start as trigger possible again
- Actions - Warm start as trigger possible again
- SNMP - Indexing problem for actions corrected
- MQTT - SSL transmission and Client-ID introduced
|
1.39
on request |
| January 7, 2020 |
- Actions - Digist authentication for HTTP(S) requests revised
- Inputs/Outputs - Filter and pulse settings adapted for new hardware drivers
|
1.38
on request |
| December 12, 2019 |
- Downgrade block - JSON enable included
- MQTT - Last Will connection topic revised
- SNMP - private authentication revised
- Date/time - weekday calculation revised
- Homepage - Action tiles expanded
- Config Up/Down Load - processing accelerated (no more timeout)
|
1.37
on request |
| December 2, 2019 |
- SNMP - Time compensation for SNMPv3 corrected
- Pulse mode - Dependencies when resetting adjusted
- REST - Greater tolerance for upper/lower case in HTTP header fields
- Actions - Clear message for counter monitoring added
- Actions - Number of possible actions increased to 30
- Actions - For HTTP(S) requests W&T placeholders are accepted
- Actions - For HTTP(S) requests greater tolerance for upper/lower case in HTTP header fields
- User page - Problems in representing W&T tags fixed
- Memory management - used address space expanded
|
1.36
on request |
| August 1, 2019 |
- SNMP - Support of downward compatible OIDs improved
- SNMP - Support up to SNMPv3
- Configuration upload - Timeout behavior optimized
- Version query expanded
- MQTT - Ping timeout corrected
- Device registration at W&T possible
|
1.35
on request |
| November 16, 2018 |
- Web-API - Cross origin request can be configured
- Rest - Cross original request can be configured
|
1.31
on request |
| October 22, 2018 |
- MQTT - uniform W&T standard topics introduced
|
1.29
on request |
| September 20, 2018 |
- Actions - Triggering by setting counter to zero optimized
- Actions - <CR> tag for line skip introduced
|
1.27
on request |
| June 28, 2018 |
- Box-to-Box - Signal detection at start optimized
- SNMP - download link for MIB corrected
|
1.24
on request |
| June 4, 2018 |
- SNMP - OIDs from preceding model are accepted
- BINARY Client - Server Addr. also configurable as name
- Configuration - internal plausibility check
|
1.23
on request |
| March 15, 2018 |
- Actions - Use of host names instead of IP revised
- Actions - Sending of SNMP trap texts corrected
- Upload of large configuration files improved
|
1.22
on request |
| January 26, 2018 |
- MQTT - Last Will added
- Network buffer processing optimized
- Actions - TCP message now also permitted on localhost
- Outputs - Resetting for pulse revised
|
1.21
on request |
| September 20, 2017 |
- MQTT Publish: QoS can be set
- MQTT Publish: Retain can be set
- SNMP: UDP ports can be set
- Outputs: Inverting revised
- Homepage: HTTP(S) communication optimized
- Firmware update: internal processes optimized
|
1.20
on request |
| July 20, 2017 |
- Restart behavior when changing the IP parameters corrected
- IO processing after restart revised
- Pulse mode: Behavior after saving corrected
- HTTPS/TLS: Processing of large data blocks optimized
- Accuracy of the internal clock improved
|
1.18
on request |
| June 28, 2017 |
- MQTT: ClientID output corrected
- MQTT: No publish without message text
|
1.17
on request |
| June 8, 2017 |
- Display of network interruptions on Home
- Actions: Output of HTTPS requests added
- Actions: Logic in IO combinations revised
- Client specifications for MSL/MTU size taken into account
- SSL network buffer management optimized
|
1.16
on request |
| May 11, 2017 |
- Website callup optimized
- Parameter transfer revised
- Pulse mode: Reset behavior corrected
|
1.15
on request |
| March 21, 2017 |
- Firmware for the 0 series
|
1.14
on request |
