W&T connects
Interfaces for TCP/IP, Ethernet, RS-232, RS-485, USB, 20mA, glass and plastic fiber optic cable, http, SNMP, OPC, Modbus TCP, I/O digital, I/O analog, ISA, PCI
Firmware:

Web-Thermograph Pt100 / Pt1000

Model 57610

Current firmware
Date Changes and comments Revision
July 8, 2020
  • Encrypted cloud transmission for maintaining function using enhanced security standards (TLS1.2), which this hardware does not support, are turned off.
 1.92
ZIP download
 Show older firmware...
Hide older firmware...
Older firmware
Date Changes and comments Revision
July 7, 2017
  • Error in cloud access fixed
Please verify that the device has Version 1.60 before updating!
 1.90
on request
March 11, 2015
  • Error in CSV output (Celsius/Fahrenheit representation) fixed
  • Problem with software support of older hardware generations fixed
Please verify that the device has Version 1.60 before updating!
 1.87
on request
September 29, 2014
  • Functionality for sending measurement values to the W&T cloud added
  • Current configuration settings added to MIB
Please verify that the device has Version 1.60 before updating!
 1.86
on request
April 16, 2014
  • SSL/TLS transmission stabilised
  • User login blocked/waits for the end of the encrypted transmission
  • System performance increased browser access accelerated
  • Error corrections made to the graphical value display
  • Encrypted e-mail sending using SSL/TLS
  • Bi-language firmware: German/English selectable
Please verify that the device has Version 1.60 before updating!
 1.83
on request
February 19, 2014
  • Flash codes for emergency access/Factory Default Reset revised
  • Encrypted e-mail sending using SSL/TLS
  • Bi-language firmware: German/English selectable
The firmware 1.82 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.82
on request
February 17, 2014
  • Password entry for language selection added
  • Encrypted e-mail sending using SSL/TLS
  • Bi-language firmware: German/English selectable
The firmware 1.81 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.81
on request
February 12, 2014
  • Encrypted e-mail sending using SSL/TLS
  • Bi-language firmware: German/English selectable
  • Problems with representing negative values in the graphical display fixed.
Before updating to V1.80 all passwords must be deleted from the device so that login is possible after the update. You can reassign them after the update.
The firmware 1.80 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.80
on request
September 3, 2012
  • Error in Java applet eliminated
  • Problems with device start with full data logger eliminated
  • Problem eliminated: Output of empty files for FTP alarm
  • Multiple DNS resolution for mail revised
  • Error output on the diagnostics page with time stamp
The firmware 1.75 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.77
on request
February 29, 2012
  • Error on internal data sheet corrected
The firmware 1.75 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.75
on request
February 10, 2012
  • Problems with DHCP functionality eliminated
  • Error in SNMP MIB corrected (57609 only)
The firmware 1.72 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.73
on request
June 27, 2011
  • Corrections in test alarm for timer triggered alarms
  • Mail: Authentication for ESMTP: larger line buffer
  • Mail: Logon for long server names failed
The firmware 1.72 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.72
on request
May 17, 2011
  • Corrections in Java applet
  • Corrections in time-synchronous output for timer trigger
The firmware 1.71 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.71
on request
April 14, 2011
  • Corrections in device BIOS
  • Updated script files for the home page
The firmware 1.70 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.70
on request
February 11, 2011
  • Ability to register devices (WuTility 3.85 and higher)
  • DNS polling now also via TCP and UDP
The firmware 1.69 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.69
on request
January 11, 2011
  • Error in device BIOS eliminated
  • Smart.htm page for display on smartphones/cell phones
  • Inputs switchable between °C, °Fahrenheit and Kelvin
The firmware 1.68 requires WuTility v.3.82 or higher for loading into devices!
Please verify that the device has Version 1.60 before updating!
 1.68
on request
October 13, 2010
  • Boot-up behavior optimized
 1.66
on request
September 7, 2010
  • Error corrected: DNS resolving for mail sending + port no. did not function
  • New W&T tag: <DN> for outputting the system name in a mail
  • Check Alarm function for testing an alarm
  • new OID; measurement values can be read via SNMP with decimal separation
  • Command line parameter for start and stop time of the CSV download
 1.65
on request
May 7, 2010
  • Progress bar for backing up the factory defaults inserted
 1.62
on request
April 7, 2010
  • Problem eliminated: Line breaks in text fields were incorrectly interpreted
 1.61
on request
January 15, 2010
  • Problem eliminated: Wrong identifier in XML configuration
  • Problem eliminated: Output format error for negative UTC offset
  • Error corrections for graphical output
  • Minimum length of Ethernet frames adjusted
  • Reset behavior in DHCP mode revised
 1.60
ZIP download
December 18, 2009
  • Send alarm/report directly over Twitter™
  • Subscribe to RSS feed
  • Error corrections for graphical output
 1.59
on request
November 24, 2009
  • Send alarm/report directly over Twitter™
  • Problems resolved: Increment/recording greater than 1 min. caused problems in CSV output
  • Various improvements in graphic display
 1.58
on request
August 27, 2009
  • Problem resolved: Entering of hex values in SNMP was rejected
  • Sensor detection after firmware update revised
  • Lockout of Save, Restore, Logout buttons with progress display
  • Problem with mail authentication resolved
 1.57
on request
June 4, 2009
  • Problem in the e-mail report function resolved
 1.56
on request
May 26, 2009
  • Problem in SNMP/UDP communication resolved
 1.55
on request
May 13, 2009
  • New user tags: <AA>, <AS>, <AN>
  • DHCP client revised
 1.54
on request
January 28, 2009
  • ESMTP authentication revised
  • Improvements in operation on switches/hubs with Mac-based authentication
  • Display problem with chart view eliminated
  • Display problem when using the integrated Java applet eliminated
  • Problem with DNS resolution eliminated
Note: For this version or higher please use WuTility v3.61 or higher
 1.53
on request
September 11, 2008
  • A/D converter for communication improved
  • Alarm routine revised
  • FTP login without password revised
  • All downloads now available as attachment
  • Java applet revised
  • Alarm display in Javascript corrected
  • Mail: "CSV-Data since last report" optimized
Note: With this version or higher please use at least WuTility 3.51 or the current version available at www.wut.de
 1.51
on request
May 28, 2008
  • Temperatures below -65 degrees C were not displayed with older hardware
  • The system name is no longer overwritten when updating, rather only when performing a Factory Default Reset
  • Internet link to www.wut.de contains only the expression "http://". This is automatically completed when updating
Note: With this version or higher please use at least WuTility 3.46 or the current version available at www.wut.de
 1.50
on request
March 18, 2008
  • Optimized handling at restart when memory is full and there are strung data records
  • Integrity of the data logger when time server fails ensured
  • XML and CSV download accelerated
  • CSV download no longer handled by EXCEL plug-in but rather using direct file download
Note: For this version and higher please use the included WuTility 3.46 or the current version available at www.wut.de
 1.49
on request
January 22, 2008
  • New menu design
  • Optimized for memory administration
  • Problem in alarm representation in the logger output corrected
Note: For this version and higher please use the included WuTility 3.46 or the current version available at www.wut.de
The new design is not initialized until you perform a factory default reset. The functions of the device are however still available even without this reset.
 1.48
on request
October 10, 2007
  • Firmware update: Timing for slow networks improved
  • Display corrections: Error in menu and graphical display eliminated
Note: For this version and higher please use the included WuTility 3.43 or the current version available at www.wut.de
 1.45
on request
September 28, 2007
  • Problem when changing over older devices to DHCP firmware eliminated
  • Improved graphical display
  • New time tags for SNMP added
Note: For this version and higher please use the included WuTility 3.43 or the current version available at www.wut.de
 1.44
on request
September 12, 2007
  • DHCP functionality added
  • New graphic function added
  • UDP behavior improved
  • Configuration remains intact after firmware update
  • New W&T tags for measured values in dotted format
  • New W&T tags for freely selectable date display
  • W&T tags in the mail subject line as well as FTP file name possible
Note: For this version and higher please use the included WuTility 3.42 or the current version available at www.wut.de
 1.43
on request
Hide older firmware...

Up