USB Redirector for

• Fixed: UsbControl, safe removing of mass storage devices
• Fixed: Honeywell USB scanners are correctly installed

The USB Redirector 3.41 must only be used with Firmware >= 1.10 [53663] and >= 1.08 [53662] and >=1.83 [53642]!

• Optimized: Setup program
• Optimized: POWEROFFTIME with USB control can be used

The USB Redirector 3.39 must only be used with Firmware >= 1.10 [53663] and >= 1.08 [53662] and >=1.83 [53642]!

• Optimized: Device release / integrate
• Fixed: Installation of a USB composite device

The USB Redirector 3.38 must only be used with Firmware >= 1.10 [53663] and >= 1.08 [53662] and >=1.83 [53642]!

• Optimized: USB port reset can be performed later after a connection is closed.
• Fixed: Display error n in the list of USB servers

The USB Redirector 3.36 must only be used with Firmware >= 1.10 [53663] and >= 1.08 [53662] and >=1.83 [53642]!

• Optimized: FTDI driver on segments with high latency time
• Fixed: Display of the owner of a device when the ABO was created using USBControl

The USB Redirector 3.34 must only be used with Firmware >= 1.10 [53663] and >= 1.08 [53662] and >=1.83 [53642]!

• Optimized: Attestation signed core drivers for Windows 10 / Server 2016
• Optimized: Faster release of devices

The USB Redirector 3.33 must only be used with Firmware >= 1.10 [53663] and >= 1.08 [53662] and >=1.83 [53642]!

• Optimized: URB_FUNCTION_SYNC_RESET_PIPE_AND_CLEAR_STALL
• Optimized: Surprise Removal accelerated
• Optimized: Attestation-signed core driver for Server 2016
• Optimized: IOCTL_INTERNAL_USB_CYCLE_PORT

The USB Redirector 3.32 must only be used with Firmware >= 1.10 [53663] and >= 1.08 [53662] and >=1.83 [53642]!

• New: Support for USB Server Gigabit 2.0 #53663
• New: The help tool USBLocations pre-installed
• New: URB Control_Transfer_Ex implemented
• Optimized: Handling of installations with activated Secure Boot
• Optimized: System response improved for installing/uninstalling the core driver
• Optimized: URB Reset Pipe and Clear Stall
• Fixed: Core driver installation under Windows 8.1 / Server 2012R2
• Fixed: Error with device handover and backup devices
• Fixed: URB Reset Pipe failed

The USB Redirector 3.30 must only be used with Firmware >= 1.10 [53663] and >= 1.08 [53662] and >=1.83 [53642]!

• Fixed: Core driver installation under Windows 8.1 / Server 2012R2

The USB Redirector 3.27 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• New: Windows 10 core driver with Attestation Signing

The USB Redirector 3.26 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Fixed: Bluescreen "System Service Exception"

The USB Redirector 3.25 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Fixed: Bluescreen after faulty USB descriptors
• Fixed: Bluescreen with UMTS sticks
• New: UAS drivers are supported

The USB Redirector 3.24 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Optional: Interactive device transfer and release of the USB device
• Fixed: Problem with device transfer and safe removal from mass storage media

The USB Redirector 3.22 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• New: Optional, forbid switching to the Windows power save move

The USB Redirector 3.21 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Fixed: "Connected" was not correctly displayed
• Fixed: Bluescreen with Soundblaster USB audio devices

The USB Redirector 3.19 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Fixed: USB control error message expanded
• Fixed: Bluescreen after reincorporating USB devices

The USB Redirector 3.15 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Fixed: Localhost is correctly resolved
• Optimized: System response improved

The USB Redirector 3.11 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Fixed: Bluescreen when calculating isochronous packets

The USB Redirector 3.09 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Fixed: Incorporation of devices without entered DNS server

The USB Redirector 3.08 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Corrected: Installation for Windows Vista and Server 2008

The USB Redirector 3.06 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Corrected: Crash with USB devices without string descriptor
• Corrected: Crash with systems having a slow CPU

The USB Redirector 3.05 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• NEW: Simultaneous joining of multiple devices is time delayed
• New: Additional IOCTL_USB_USER_REQUEST implemented
• Corrected: Reset was not always triggered on the device after a connection was closed
• Corrected: Bluescreen after joining a defective USB device
• Optimized: Old registry branches were not deleted

The USB Redirector 3.03 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• NEW: Permanent connection to the USB Server (optional)

The USB Redirector 3.00 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)!

• Handling of isochronal IN pipes optimized
• Support for changing MaxPacketSize
• Installation routine optimized
• NEW: Support for editable port descriptions

The USB Redirector 2.93 must only be used with Firmware >= 1.08 (53662) and >= 1.83 (53642)

• Optimized: Handling of isochronous transfers
• Optimized: Increased TCP send buffer size for UNRBs
• Optimized: Closing the configuration tool
• Optimized: Calling the descriptors

The USB Redirector 2.89 must only be used with Firmware >= 1.82 (53642) and >= 2.61 (53641) !

• Corrected: Incorrect USB Port Sring for Power-Power-Reset

The USB Redirector 2.87 must only be used with Firmware >= 1.82 (53642) and >= 2.61 (53641) !

• Optimized: Uninstalling of the USB Redirector
• Corrected: USBControl passed an incorrect USB Port String

The USB Redirector 2.86 must only be used with firmware >=2.61 (53641) and >=1.82 (53642) !!!

• Optimized: Uninstalling of the USB Redirector
• Optimized: USB port added to power data
• Optimized: Isochron received data are processed faster
• Optimized: USB Redirector now always minimized at Autostart
• New: USB_GET_TOPOLOGY_ADDRESS is supported
• Corrected: Windows freezes after a fault
• Corrected: Processing of the "Extended Properties Descriptor"

The USB Redirector 2.85 must only be used with firmware >=2.61 (53641) and >=1.78 (53642) !!!

• Optimized: Removing or unplugging a USB device
• Corrected: Windows freezes after a fault

The USB Redirector 2.83 must only be used with firmware >=2.61 (53641) and >=1.78 (53642) !!!

• Optimized: UsbControl expanded
• Corrected: Error after updating the USB Redirector under Win XP
• Corrected: Long passwords (>12 characters) cause a crash

The USB Redirector 2.82 must only be used with firmware >=2.61 (53641) and >=1.78 (53642) !!!

• New: Start USB audio transfers as quickly as possible
• Corrected: Incorrect error message "No device on selected port"
• Corrected: Abort_Pipe didn’t cancel certain URBs

The USB Redirector 2.81 must only be used with firmware >=2.61 (53641) and >=1.78 (53642) !!!

• New: Mass storage devices are safely unmounted
• New: Updated cross certificate
• Corrected: Multiple errors in Device_Capabilities
• Corrected: USB audio crash after Clear_Stall

The USB Redirector 2.80 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Corrected: Resolving host names without domain suffix

53641/53642:
The USB Redirector 2.75 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Corrected: Bluescreen when invoking special interface routines

53641/53642:
The USB Redirector 2.74 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• New: New setup dialog

53641/53642:
The USB Redirector 2.73 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Corrected: A USB device was switched off by Cycle Port
• Corrected: Display error on USB Redirector

53641/53642:
The USB Redirector 2.71 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Corrected: Erroneous PowerCtrl bits in hub descriptor
• Optimized: Deinstallation process

53641/53642:
The USB Redirector 2.70 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Corrected: Erroneous display after loading the inventory list
• Corrected: Error when switching a subscription between permanent/temporary

53641/53642:
The USB Redirector 2.65 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Optimized: Drive letters and COM port numbers can be displayed
• Optimized: Behavior and representation of the interface improved
• Corrected: Release of a busy device results in a reset

53641/53642:
The USB Redirector 2.64 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Optimized: Isochronal data transmission
• New: Audio interface can be turned off with USB video device

53641/53642:
The USB Redirector 2.62 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Corrected: Large isochronal transfers cause a crash
• Corrected: Bluescreen when copying 0 bytes of descriptors

53641/53642:
The USB Redirector 2.61 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Corrected: Number of USB ports can be called
• Corrected: Passport saving can be enabled/disabled
• Optimized: Appearance and behavior of the USB Redirector
• Optimized: USB video data processing
• New: Info dialog includes network and safety setting
• New: Mass storage media can now be integrated write-protected

53641/53642:
The USB Redirector 2.60 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Corrected: Installation problems in Windows XP

53641/53642:
The USB Redirector 2.52 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Optimized: Isochronal video data transmissions (webcams)
• New: Retrieval interval for video images is configurable (one image every x sec.)

53641/53642:
The USB Redirector 2.51 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Optimized: Performance data statistics expanded
• Optimized: Isolate USB audio devices
• Corrected: Bluescreen with defective interface descriptors
• Corrected: Empty device list in USBControl

53641/53642:
The USB Redirector 2.47 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Optimized: Power reset when enabling devices
• Corrected: Inserting devices with defective interface declarations
• Corrected: Loading saved configurations
• Corrected: Installation with Secure Boot turned on
• Corrected: Link remains intact after the update

53641/53642:
The USB Redirector 2.45 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Optimized: Uninstalling of the USB Redirector
• Corrected: Isochronal data transfer at low bandwidth
• Corrected: Bluescreen with SetConfig
• New: Bundling of video data at low bandwidth

53641/53642:
The USB Redirector 2.43 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Optimized: Acceleration of the isochronal transfer
• Corrected: Bluescreen with eMPIA drivers
• New: IOCTL_USB_GET_HUB_CAPABILITIES

53641/53642:
The USB Redirector 2.41 must only be used with firmware >=2.61 (53641) and >=1.56 (53642) !!!

• Optimized: USB Port Reset
• Optimized: Plug+Play properties of the USB Redirector
• Corrected: Additional interface after "Set Config"
• Corrected: Blue screen for "Set Config" in very rare cases
• Corrected: Blocking data reception by unacknowledged send data
• New: A virtual root hub
• Neu: Popup messages can be turned off
• New: Support for extended properties OS feature descriptors

53641:
USB Redirector 2.32 must only be used with firmware > 2.61 !!!

• Optimized: Direct switching to a permanent subscription
• Corrected: Device_Capabilities were incorrectly addressed
• Corrected: Long host names were not supported
• Corrected: MultiConfig devices were reset

53641:
USB Redirector 2.22 must only be used with firmware > 2.61 !!!

• Optimized: Status messages from the USB Redirector
• Optimized: USB_Cycle-Port
• New: Isochronal bandwidth limitation can be configured
• Corrected: Blue screen with verifier is turned on
• 53642 new: Complete shutoff of the USB ports

53641:
USB Redirector 2.20 must only be used with firmware > 2.61 !!!

• Optimized: Bandwidth limitation increased
• Optimized: Resolve host names

53641:
USB Redirector 2.16 must only be used with firmware > 2.61 !!!

• New: Windows 8 and Server 2012 are supported

53641:
USB Redirector 2.15 must only be used with firmware > 2.61 !!!

• New: USB location IDs are generated
• Fixed: Select Configuration results in a deadlock
• Fixed: Pending requests after an unplug results in a blockade
• Optimized: Generation of a PDO
• Optimized: Faster linkage after USB reset
• Optimized: USB Port Reset

USB Redirector 2.14 must only be used with firmware > 2.61 !!!

• Optimized: UsbControl
• Fixed: Error when deleting an active backup device
• Fixed: USB sent data with too little data error
• Fixed: Association of drive letters with USB devices
• Fixed: Inventorying error
• Fixed: IOCTL_INTERNAL_USB_GET_PORT_STATUS error
• Fixed: Error when double-buffering URBs

USB Redirector 2.13 must only be used with firmware > 2.61 !!!

• Optimized: Instance designators
• Optimized: Canceling of URBs
• Eliminated: Sorting of new USB devices

USB Redirector 2.10 must only be used with firmware > 2.61 !!!

• Eliminated: Incorrect implementation of QueryBusTimeEx()
• Eliminated: Memory corruption (blue screen)
• Optimized: In Version 2.10 and higher all configuration options set are carried over to future versions

USB Redirector 2.10 must only be used with firmware > 2.61 !!!

• Optimized: Enabling and reincorporating a USB device

USB Redirector 2.05 must only be used with firmware > 2.61 !!!

• Eliminated: 30 - 60 sec. block when the connection is interrupted.
• Optimized: System password can be entered

USB Redirector 2.04 must only be used with firmware > 2.61 !!!

• Eliminated: USB device driver installation

USB Redirector 2.02 must only be used with firmware > 2.61 !!!

• Eliminated: USB Control error 1169 / 1168
• Optimized: Interrupt transfer accelerated

USB Port Redirector 2.01 must only be used with firmware > 2.61 !!!

• New: Mass memories can be limited to one session (e.g. terminal servers)
• Eliminated: Automatic subscriptions were incorrectly stored
• Eliminated: Multiple small errors in USBD structures
• Optimized: Search for USB servers (network scan)
• Optimized: USB frame counter
• Optimized: Serial numbers with NUL character

USB Port Redirector 2.00 must only be used with firmware > 2.61 !!!

• Corrected: Transfer buffer optimized

USB Redirector 1.99 must only be used with firmware > 2.61 !!!

• Optimized: New parameters for UsbControl
• Optimized: Frame counter transfer
• Corrected: Transfer buffer for isochronal data
• Corrected: QueryBusTimeEx provides wrong results
• New: Isochronal status codes are translated in Windows
• New: *.msi download format

USB Redirector 1.98 must only be used with firmware > 2.61 !!!

• Optimized: Two new parameters for UsbControl
• Optimized: Two URBs can be sent at the same time to the USB server.
• Optimized: Host name can be displayed instead of IP address.
• New: USB_BUS_INTERFACE_USBDI v3
• New: *.msi download format

USB Port Redirector 1.97 must only be used with firmware > 2.61 !!!

• Fixed: USB_BUS_INTERFACE_USBDI is correctly replied to
• Fixed: Crash caused by incorrect network data
• New: *.msi download format

USB Redirector 1.96 must only be used with firmware > 2.61 !!!

• Fixed: Blue screen after bulk requests
• New: MSI package for installation now includes both languages and is compatible with 32- and 64-bit systems

USB Port Redirector 1.95 must only be used with firmware > 2.61 !!!

• Fixed: Ignore serial number
• New: Host controller can be reached as an HCD device

USB Redirector 1.94 must only be used with firmware > 2.61 !!!

• Fixed: Windows standby mode resulted in a blockade
• Fixed: Misleading error message

USB Redirector 1.93 must only be used with firmware > 2.61 !!!

• Optimized: USB Port Reset
• Optimized: USB Language

USB Redirector 1.91 must only be used with firmware > 2.61 !!!

• New: Default setting for "Add" button configurable
• New: Configuration via command line tool "USBControl"
• Optimized: Plug & play behavior
• Optimized: Port reset URB
• Fixed: Cancel URB

USB Port Redirector 1.90 must only be used with firmware > 2.61 !!!

• Optimized: Instance identifier
• New: Ignore serial number

USB Redirector 1.84 must only be used with firmware > 2.60 !!!

• New: Windows firewall supported
• Optimized: "Set Config"
• Fix: Location String corrected
• Fix: "Abort Pipe" cancelled to many data

USB Redirector 1.82 must only be used with firmware > 2.50 !!!

• New: Virtual systems without USB are supported
• New: Get Port Status
• Optimized: Config descriptor checking
• Optimized: Cancel routines
• Fixed: Canceling a URB
• Optimized: PowerCapabilities
• Fixed: Cooperation parameters
• Optimized: Automatic subscription
• Optimized: Device resetting

USB Redirector 1.81 must only be used with firmware > 2.50 !!!

• New: WMI queries are supported
• New: Calling MS Feature descriptors
• Optimized: USB serial number validated
• Optimized: No. of max. interfaces
• Optimized: iPhone / HTC Desire
• Optimized: PowerCapabilities

USB Redirector 1.73 must only be used with firmware > 2.50 !!!

• New: Devices can be copied by another PC
• New: "Reset Device", resets the USB-Server
• Optimized: Status texts, especially "Communication problem"
• Optimized: USB device is transferred to the PC unconfigured

USB Redirector 1.71 must only be used with firmware > 2.50

• Error corrected: Access to Windows registry
• Optimized: Canceling a URB
• Optmized: Response for Abort_Endpoint

USB Redirector 1.62 must only be used with firmware > 2.30

• Error corrected: DNS suffixes were not previously taken into account.
• Error corrected: Port Reset could result in ejection of the device
• Error corrected: "Enable Device" when shutting Windows down
• New: The WBM port on the USB Server can now be edited

USB Redirector 1.60 must only be used with firmware > 2.30

• Error eliminated: Improvements in URB_FUNCTION_ABORT_PIPE

USB Redirector 1.55 must only be used with firmware > 2.26

• Error eliminated: Disable and immediately reenable device
• Error eliminated: Virtual USB devices are power managed
• Error eliminated: Unnecessary set interface commands
• New: Warning for older firmware (< Version 2.26)

USB Redirector 1.54 must only be used with firmware > 2.26

• Error eliminated: Number of bytes for user mode IOCTLs corrected
• Error eliminated: When applying subscriptions
  registry handles were lost
• Error eliminated: Naming scheme for USB location was changed
  for Vista and later
• New: Error codes are now output as a text message
• New: Device pool, backup devices can be specified
  (e.g. multiple dongles)

USB Redirector 1.53 must only be used with firmware > 2.26

• Error corrected: Device with the same serial number will function
• Error corrected: Invalid language codes are checked
• New: Minimize as tray icon
• New: Subscription mode as long as the application runs
• New: Quick Plug/Unplug button in the toolbar

USB Redirector 1.51 must only be used with firmware > 2.26

• Error eliminated: Processing of received data
• Error eliminated: display error of IP address
• New: Subscription mode for printer
• New: Subscription mode with time restriction
• Speed optimized
• Direct access to USB Server Web page

USB Redirector 1.44 must only be used with firmware > 2.26

• Error corrected: Bulk/Interrupt, wrong flag set
• Error corrected: Wrong error message for too many interfaces
• Error corrected: wMaxPacketSize in endpoint descriptor incorrectly read
• Management of pipe data structures improved

• Error in signature of Setup.exe corrected
• Additional optimizations for USB devices with multiple configurations
• Kernel trace profile for debug added
• Windows optimization after a port reset emulated

• Additional improvements in bulk transfer for large data amounts
• Debug outputs expanded
• Timeout for port resets extended to 20s
• Cosmetic defect corrected

• Instance collisions after unplug events fixed
• Reinitializing of URBs on same pipe optimized
• Debug outputs expanded (statistics bulk packets)
• Additional URB types and IOCTLs implemented
• Configuration tool optimized